CRC ALU H T
1. GENERAL DESCRIPTION
High temperature aluminium coating.
CRC ALU HT is a high temperature paint based on silicone resins and active aluminium pigments.Alu H.T. is designed to build a hard lasting finish that will not burn off, chip or peel at high temperatures.
2. FEATURES of CRC ALU H T
High thermal stability: resists temperatures up to 600°C.
Excellent coverage.
High durability.
Quick drying at room temperature.
Very good resistance to temperature fluctuations.
Good weather stability. Although some loss of gloss can be noticed after extended exposure.
Totally lead and chromate free.
No chlorinated and no aromatic solvents.
Aerosols use dimethylether (DME) propellant for controlled application and film properties.
3. APPLICATIONS of CRC ALU H T
Stove pipes
Stoves
Heaters
Kilns
Incinerators
Chimneys
Exhaust manifolds
Headers
Engines3
Ovens
Steam pipes
4. DIRECTIONS of use for CRC ALU H T
Shake aerosol can very well for at least one minute after agitator ball is free. Stir or mix bulk product well to obtain a homogeneous dispersion. Repeat frequently while using.
Apply to a clean, degreased, dry surface for best results. Remove rust and scale with a wire brush.
Apply in light, even coats; best results are obtained with 2 lighter rather than 1 heavy coat. Additional coats can be applied after 15-30 minutes.
Complete curing occurs during use, typically after 1 h @ 200°C or 45 min. @ 250°C.
When spraying is finished, clean aerosol valve by turning can upside down and pressing button until only propellant escapes. If clogging occurs, remove button and clean orifice with fine wire.
Do not use on energised equipment. Use in well ventilated area.
A safety data sheet (MSDS) according EU directive 93/112 is available for all CRC products.
5. TYPICAL(*) PRODUCT DATA (without propellant)
Appearance : mat aluminium finish
Resin type : silicone
Pigment type : non-leafing aluminium
Specific gravity (@ 20°C)
- aerosol : 0,99
- bulk : 1,11
Flash point (solvents)
- aerosol : -4°C
- bulk : 42°C
Coverage (30 µm, dry)
- aerosol : approx. 2,7 m2/can (400 ml)
- bulk : TBD
Drying times
to touch : 15 min @ 20°C (45% RH)
to : 24 h @ 20°C (45% RH)
to complete cure : 1 h @ 200°C
Recommended film thickness : 25-30 µm
Thinner / cleaner : M.E.K., acetates
Dry film properties (on degreased metal)
Heat resistance (ASTM D-2485-68)
Method 1 (24 h cont.) : 600°C
Method 2 (cycling) : 635°C
Adhesion on steel (NFT 30038) : 0/1
Flexibility : pass
(after heating to 600°C, 6 mm mandrel, visual)
6. PACKAGING of CRC ALU H T
aerosol : 12 x 400 ml
bulk : 750 ml
CRC AEROSOL, ELECTRICAL MAINTENANCE Spray, CRC 2-26, CRC CO CONTACT CLEANER, CRC LECTRA CLEAN, CRC N F Precision, ONLINE CONTACT CLEANER, CRC URETHANE ISOLATION RED, CRC PLASTIC 70, CRC BATTERY TERMINAL COATING, CRC 3-36, CRC 5-56, CRC GASKET REMOVER, CRC FAST DRY DEGREASER, GALVABRITE, CRC RUST REMOVER, CRC COPPER PASTE, CRC METAL FREE PASTE, CRC HAND CLEANER, CRC ANTI FRICTIONAL TEFLON COATING, CRC FREEZE 75, CRC SP-400, CRC SP - 350