1. GENERAL DESCRIPTION
Heavy duty non-chlorinated cleaner.
An innovative solvent blend that contains no chlorinated solvents and no ozone-depleting components. CRC's Industrial Degreaser is excellent for use where rapid turnaround is necessary and low flash point solvents can be used. Dissolves and removes greases, oils, lubricants, adhesives and contaminants from equipment, machinery, motors and metal parts. Especially formulated for degreasing electric motors; the common coating types used on electric windings are not attacked.
2. FEATURES
Cuts through dirt, penetrates quickly under it.
Attacks encrusted residues.
Fast evaporation to minimize downtime.
Easy "in place" cleaning.
Leaves no residues.
Non-corrosive and non-staining.
Safe on most plastics, coatings and rubbers (test prior to use).Low odor.
Aerosol is equipped with the 360° (upside-down) spray valve and extension tube for added
convenience.
Aerosol is pressurized with non-flammable CO2 propellant, giving an active product content of over
97%.
Authorized by USDA for use in the food industry, according K1, K2.
3. APPLICATIONS
Electric motors
Pumps
Generators
Bearings
Air tools
Mechanical brakes and clutches
Chains
Sprockets
Wire ropes
Dies
Moulds
Air conditioners and compressors
Fork lift trucks
Material handling equipment
General degreasing and oil removal.
TECHNICAL DATA SHEET
2/2
CRC INDUSTRIAL DEGREASER
Ref. : 10113
4. DIRECTIONS
Apply liberally and allow excess to run off. Air dry or dry with absorbent cloth. Repeat if necessary.
Use extension tube for hard-to-reach areas.
In dipping applications, agitation accelerates cleaning. Dip tank should be covered when not in use to avoid undue evaporation.
May also be used by wiping with a clean rag or brushing.
Check solvent compatibility for your application before use. If in doubt, test a small area or call the manufacturer of the equipment. Do not use on sensitive electronic equipment.
Use with adequate ventilation. Do not use on energized equipment. Allow drying thoroughly and venting before reactivating system.
A safety data sheet (MSDS) according EU directive 93/112 is available for all CRC products.
After cleaning, use CRC 3-36 for protection and lubrication.
5. TYPICAL PRODUCT DATA (without propellant)
Appearance : colorless liquid, sweet odor
Specific gravity (@ 20°C) : 0.808
Boiling range : 100-170 °C
Vapor density (vs air = 1) : 4
Freezing point : < -30 °C
Evaporation rate (vs ether = 1) : 19
Flash point (closed cup) : 25°C
Kauri - Butanol value : > 150
Hildebrand solubility parameter (calc.) : 8.206
Hydrogen bonding index (calc.) : 0.384
Fractional polarity (calc.) : 0.037
Viscosity (@ 20°C, calc.) : 0.76 mPa.s
Surface tension (@ 25°C est.) : 23 mN/m
Plastics compatibility : poor, test prior to use
ODP (vs F11 = 1) : 0.00
CRC AEROSOL, ELECTRICAL MAINTENANCE Spray, CRC 2-26, CRC CO CONTACT CLEANER, CRC LECTRA CLEAN, CRC N F Precision, ONLINE CONTACT CLEANER, CRC URETHANE ISOLATION RED, CRC PLASTIC 70, CRC BATTERY TERMINAL COATING, CRC 3-36, CRC 5-56, CRC GASKET REMOVER, CRC FAST DRY DEGREASER, GALVABRITE, CRC RUST REMOVER, CRC COPPER PASTE, CRC METAL FREE PASTE, CRC HAND CLEANER, CRC ANTI FRICTIONAL TEFLON COATING, CRC FREEZE 75, CRC SP-400, CRC SP - 350
