Crc Lectra Clean
1. GENERAL DESCRIPTION
Crc Lectra Clean is Non-flammable electrical parts cleaner.
CRC Lectra Clean is a heavy duty degreaser with strong cleaning action and fast evaporation.The chlorinated solvent blend is designed to quickly and effectively clean electrical/mechanical components, preventing failures and malfunctions caused by contaminants such as dust, dirt, grease and oil.
2. FEATURES of Crc Lectra Clean
Crc Lectra Clean Contains no ozone depleting chemicals: ODP = 0.
Crc Lectra Clean Gives no contribution to global warning : GWP = 0.
Very low ozone creation potential : OCP : 0,05.
Crc Lectra Clean Promotes operating efficiency.
Contributes to prolonged equipment life.
Crc Lectra Clean Evaporates quickly and leaves no residue.
Crc Lectra Clean is aNon-staining, non-corrosive and non-conductive.
Crc Lectra Clean has No flash point.
Crc Lectra Clean May be harmful to some plastics, rubbers, adhesives and paints. (Test prior to use.)
Crc Lectra Clean Aerosols are equipped with the 360° (upside-down) spray valve for added convenience
Pressurised with non-flammable CO2 propellant, giving an active product content of 97%.
3. APPLICATIONS of Crc Lectra Clean
Crc Lectra Clean is An effective heavy duty degreaser for :
Air tools
Bearings
Compressors
Chains & Wire ropes
Dies & molds
Mechanical brakes & clutches
Motors
Generators
Tools
Corroded machinery and parts.
4. DIRECTIONS for use of Crc Lectra Clean
Apply liberally by spraying or dipping and allow excess to run off. Use extension tube for hard-to-reach areas. In dipping bath applications, agitation enhances cleaning action. May also be applied by wiping or by brushing.To clean equipment interior, covers, plates, etc. should be removed prior to product application.
Allow to air dry or dry with absorbent cloth. After cleaning, use CRC 2-26 for lubrication and protection.
Crc Lectra Clean May attack some plastics, rubbers, adhesives and paints. Do not use on polycarbonate or polystyrene. If in doubt, test on a small area before using or contact the manufacturer of the equipment.
Do not use on sensitive electronic equipment such as tape desks,VCR’s, computers, etc. Use one of CRC’s contact cleaner products for this.
Use only in well ventilated area.
A safety data sheet (MSDS) according EU93/112 is available for all CRC products.
TYPICAL PRODUCT DATA (without propellant)
Appearance : clear liquid
Odour : chlorinated solvent
Distillation range : 85-125°C
Freezing point : < -20°C
Specific gravity (@ 20°C) : 1,50
Vapour density (vs. air = 1) : > 4
Kauri-Butanol value : 125
Flash point (closed cup) : none
Evaporation rate (vs. ether = 1) : 4
Non-volatile content : < 50 ppm
Surface tension (@ 20°C) : 32 mN/m
Dielectric constant (@ 1000 Hz) : 3,0 ± 0,5
Drying time (vertical)(**) : < 0,5 hrs.
0,5
Drying time (vertical)(**) : < 0,5 hrs.
CRC AEROSOL, ELECTRICAL MAINTENANCE Spray, CRC 2-26, CRC CO CONTACT CLEANER, CRC LECTRA CLEAN, CRC N F Precision, ONLINE CONTACT CLEANER, CRC URETHANE ISOLATION RED, CRC PLASTIC 70, CRC BATTERY TERMINAL COATING, CRC 3-36, CRC 5-56, CRC GASKET REMOVER, CRC FAST DRY DEGREASER, GALVABRITE, CRC RUST REMOVER, CRC COPPER PASTE, CRC METAL FREE PASTE, CRC HAND CLEANER, CRC ANTI FRICTIONAL TEFLON COATING, CRC FREEZE 75, CRC SP-400, CRC SP - 350
