CRC Penetrating Oil + Mos2
GENERAL DESCRIPTION
CRC Penetrating Oil + Mos2 is a Quick acting penetrating and lubricating oil.
CRC Penetrating Oil + Mos2 is A no compromise penetrating product that attacks rust and corrosion, penetrating through oxides and soil to free corroded fasteners and mechanical components. Its low surface tension formulation quickly disperses rust, scale and corrosion, aiding disassembly of close tolerance fasteners and assemblies. Penetrating Oil + MoS2 is based on a refined paraffinic oil, inhibitors and contains MoS2 solid lubricant for reduced wear.
CRC Penetrating Oil + Mos2 FEATURES
Penetrates into hard-to-reach areas quickly.Disperses rust, scale and other oxides.
Frees metal parts seized by dirt, rust, corrosion or dried-up greasy deposits.
Eases quick disassembly of mechanical components, fittings, assemblies, nuts and bolts and other close tolerance fasteners.
Leaves a solid lubricating MoS2 film.
Reduces wear and facilitates future disassembly.
Lowers maintenance costs.
Reduces scrap rate of seized parts.
Does not contain silicones.
Safe for all metals and for most plastics and rubbers (if in doubt, on-the-job testing prior to use is advised).
Aerosols are equipped with the 360° (upside-down) spray valve and extension tube for added convenience.
Aerosols are pressurised with non-flammable CO2 propellant, giving an active product content of over 97%.
CRC Penetrating Oil + Mos2 Specifications : meets the requirements of VV-P-216B
- authorised for military applications NSN 9150-13-113-7341
CRC Penetrating Oil + Mos2 APPLICATIONS
Seized and rusted nuts and bolts
Locks and hinges
Screwed parts
Equipment disassembly
Corroded fasteners
Valves
Air tools
Chains and conveyors
Agricultural equipment
DIRECTIONS for use of CRC Penetrating Oil + Mos2
Apply liberally, saturating problem areas. Use extension tube for hard-to-reach areas.
Allow a few minutes for penetration; tap joint lightly to aid penetration.
Repeat if necessary for stubborn joints, fasteners and assemblies.
If necessary, to be removed by CRC Fast Dry Degreaser or CRC Industrial Degreaser.
A safety data sheet (MSDS) according EU directive 93/112 is available for all CRC products.
TYPICAL PRODUCT DATA (without propellant) of CRC Penetrating Oil + Mos2
Appearance : blackish-grey liquid
Specific gravity (@ 20°C) : 0,82
Flash point (open cup) : 75°C
Pour point : < -50°C
Surface tension (@ 20°C) : 26 mN/m
Horizontal spread(25 µl, 24 h, @20°C) : 90 cm2
Solvent dissipation (@ 20°C, thin film) : 2-4 h
Film properties (after evaporation of solvent)
Specific gravity (@ 20°C) : 0,88
Dynamic viscosity (@ 20°C) : 52 mPa.s
Solid lubricant content : 0,6% wt
Solid lubricant particle size : 90% below 1 µm; max. 3 µm
CRC AEROSOL, ELECTRICAL MAINTENANCE Spray, CRC 2-26, CRC CO CONTACT CLEANER, CRC LECTRA CLEAN, CRC N F Precision, ONLINE CONTACT CLEANER, CRC URETHANE ISOLATION RED, CRC PLASTIC 70, CRC BATTERY TERMINAL COATING, CRC 3-36, CRC 5-56, CRC GASKET REMOVER, CRC FAST DRY DEGREASER, GALVABRITE, CRC RUST REMOVER, CRC COPPER PASTE, CRC METAL FREE PASTE, CRC HAND CLEANER, CRC ANTI FRICTIONAL TEFLON COATING, CRC FREEZE 75, CRC SP-400, CRC SP - 350