Pelton Turbine
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Pelton Turbine - Getai Turbine
Francis Turbine - Getai Turbine
Kaplan Turbine - Getai Turbine
Pelton Wheel Turbine
Water Turbine Generator
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: Frecuencia: |
50/60HZ |
Runner Diameter: |
~ 3m |
Getai Hydropower is one of the leading Pelton Turbine manufacturers. Our Pelton Turbine Generator, Pelton Turbine Efficiency, Pelton Runner has high quality and competitive price, and you can see the Application Of Pelton Turbine.
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points.
Flow inside bucket
Shenyang Getai Hydropower Equipment Co.,Ltd main products: Pelton Turbine, Francis Turbine, Kaplan Turbine, Tubular Turbine, Pelton Turbine Generator, Francis Turbine Generator, Double Francis Turbine, Pelton Turbine Formula, welcome to our factory!
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter.
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
≤ |
≤ |
||||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
Pelton Turbine Generator
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Pelton Turbine - Getai Turbine
Francis Turbine - Getai Turbine
Kaplan Turbine - Getai Turbine
Pelton Wheel Turbine
Water Turbine Generator
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: |
50/60HZ |
Runner Diameter: |
~ 3m |
Lift Span |
30-50 years |
Getai Hydropower is one of the leading Pelton Turbine manufacturers. Our Pelton Turbine Generator, Pelton Turbine Efficiency, Pelton Runner has high quality and competitive price, and you can see the Application Of Pelton Turbine.
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter
Shenyang Getai Hydropower Equipment Co.,Ltd main products: Pelton Turbine, Francis Turbine, Kaplan Turbine, Tubular Turbine, Pelton Turbine Generator, Francis Turbine Generator, Double Francis Turbine, Pelton Turbine Formula, welcome to our factory!
Forged Entire CNC Machined Pelton Runner
Forging could considerably improve metal's organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear steel is generally stronger and more reliable than castings part.
Pelton Turbine - Getai Turbine
Francis Turbine - Getai Turbine
Kaplan Turbine - Getai Turbine
Pelton Wheel Turbine
Water Turbine Generator
Project Basic Information
Project Name: Minas-San Francisco HPP
Project Location: Ecuador
Pelton runner pitch diameter: 2460mm.
OD: 3179mm
Net Weight: 13300KG
Buckent No. 21
Output:
Product Introduction
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Getai Hydropower is Pelton Turbine Experiment, Francis Turbine Diagram, Francis Turbine Working, Pelton Turbine For Sale factoty.
Performance comparison table of forging parts and casting parts
Performance test of forging part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
|||||
Standard value |
≥795 |
≥620 |
≥15 |
≥45 |
≥50 |
230~295 |
|||||
Actual value |
Horizontal |
815 |
655 |
107 |
102 |
110 |
259 |
256 |
253 |
||
Vertical |
820 |
660 |
67 |
149 |
152 |
136 |
256 |
257 |
257 |
Performance test of casting part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
||||
Standard value |
≥750 |
≥550 |
≥15 |
≥35 |
≥50 |
221~286 |
||||
Actual value |
770 |
610 |
17 |
50 |
84 |
88 |
85 |
252 |
255 |
254 |
Forged Entire CNC Machined Francis Runner
Forging could considerably improve metal’s organizational structure and mechanical property.
Pelton Turbine - Getai Turbine
Francis Turbine - Getai Turbine
Kaplan Turbine - Getai Turbine
Pelton Wheel Turbine
Water Turbine Generator
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Getai Hydropower is a China supplier of Francis Turbine, Francis Turbine Generator, Francis Turbine Parts, Francis Runner, Construction And Working Of Francis Turbine. We have a complete quality management system. Choose us, you can be get most careful and thoughtful service!
Forged Integrally +100% CNC Machining Francis Turbine Runner
In the case the high head Francis runner with long and narrow passageway which is hard for entire CNC machining or the runner size exceeds the forging range which can not be forged integrally, GETAI applied a procedure by dividing the runner to two parts which consisted of crown with half vanes and band with rest half, both two parts can be forged integrally with entire CNC machining and welding assembled in final. The welding applied to the middle of vane, where is convenient for single pass welding without touch of potential crack area, the operation security and service life are improved largely.
Samples exhibited below is for forged integrally+100% CNC machined Francis turbine runner (half part) which finished by our five axis linkage CNC machine.
Getai Hydropower is Pelton Turbine Experiment, Francis Turbine Diagram, Francis Turbine Working, Pelton Turbine For Sale factoty.
Francis turbine
Francis turbines are built in a compact structure, with high efficiency, and can be applied to a wide range of water heads. This feature makes the Francis turbine type a widely used one around the world. The key Francis turbine components includes Runner, Distributor, Main shaft, Main shaft seal, Turbine guide bearing, Governor, among other.
Pelton Turbine - Getai Turbine
Francis Turbine - Getai Turbine
Kaplan Turbine - Getai Turbine
Pelton Wheel Turbine
Water Turbine Generator
Application Scope:
Application: |
Francis Water Turbine Generator Unit |
Water head: |
20 ~ 700m |
Output: |
1000MW |
Frequency: |
50/60HZ |
Runner diameter |
~ 10m |
Life Span |
30-50 years |
Getai Hydropower is a China supplier of Francis Turbine, Francis Turbine Generator, Francis Turbine Parts, Francis Runner, Construction And Working Of Francis Turbine. We have a complete quality management system. Choose us, you can be get most careful and thoughtful service!
Pelton Turbine Design, Francis Turbine Design, Kaplan Turbine Design company China.
Product Introduction
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
≤ |
≤ |
||||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
Pelton Turbine Rehabilitation, Kaplan Turbine Rehabilitation, Francis Turbine Rehabilitation China.
Francis Turbine Generator
Francis turbines are built in a compact structure, with high efficiency, and can be applied to a wide range of water heads. This feature makes the Francis turbine type a widely used one around the world. The key Francis turbine components includes Runner, Distributor, Main shaft, Main shaft seal, Turbine guide bearing, Governor, among other.
Application Scope:
Application: |
Francis Water Turbine Generator Unit |
Water head: |
20 ~ 700m |
Output: |
1000MW |
Frequency: |
50/60HZ |
Runner diameter: |
~ 10m |
Life Span |
30-50 years |
Getai Hydropower is a China supplier of Francis Turbine, Francis Turbine Generator, Francis Turbine Parts, Francis Runner, Construction And Working Of Francis Turbine, Francis Turbine Design.
Product Introduction
Buy low price, high quality Hydraulic Turbine Generator, Hydro Turbine Runner, Water Turbine Hydro Power, 100kw Hydro Turbines, choose our products,Getai Hydropower is the leading factory & Company, Warmly welcome new and old customers to visit and patronize!
Double Francis Turbine
The key Double Francis turbine components includes Runner, Distributor, Main shaft, Main shaft seal, Turbine guide bearing, Governor, among other.
Application Scope:
Water Head: |
|
Output: |
|
Frequency: |
50/60HZ |
Runner Diameter: |
|
Lift Span |
30-50 years |
Getai Hydropower is a China supplier of Francis Turbine, Francis Turbine Generator, Francis Turbine Parts, Francis Runner, Construction And Working Of Francis Turbine.
Product Introduction
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
≤ |
≤ |
||||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
We also provide Casting Pelton Runner, Forged Pelton Runner, Casting Guide Vane, Francis Runner Band Heat Treatment, Pelton Turbine.
Kaplan & Tubular Turbine
Kaplan Turbine is suitable for medium & low water head and large flow power plants. With same water head, the Kaplan runner speed is higher than that of the Francis'. The Kaplan runner blade can be either fixed and rotatory. The key components include: Kaplan runner, Distributor, Main shaft, Main shaft seal, Turbine guide bearing, Governor, Draft tube, Spiral case.
Tubular Turbines are suitable to lower water head, is a kind of horizontal turbine with straight flow channel. There is no spiral case in Tubular turbine, and its blades can be fixed or rotatory. The key components include: Tubular runner, Distributor, Turbine guide bearing, Governor among other.
Our Kaplan &Tubular Turbine has the features with Kaplan Turbine Design, Kaplan Turbine Advantages. Best quality and factory price will give you
Application scope:
|
Kaplan turbine |
Tubular Turbine |
Water Head: |
3 ~ 80m |
2 ~ 25m |
Output: |
~ 200MW |
~ 57MW |
Frequency: |
50/60HZ |
50/60HZ |
Runner Dia.: |
1 ~ 11m |
1 ~ 7m |
We also provide Casting Pelton Runner, Forged Pelton Runner, Casting Guide Vane, Francis Runner Band Heat Treatment, Pelton Turbine.
Product Introduction
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
≤ |
≤ |
||||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
Buy low price, high quality Hydraulic Turbine Generator, Hydro Turbine Runner, Water Turbine Hydro Power, 100kw Hydro Turbines, choose our products,Getai Hydropower is the leading factory & Company, Warmly welcome new and old customers to visit and patronize!
Pelton Turbine
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: Frecuencia: |
50/60HZ |
Runner Diameter: |
~ 3m |
Getai Hydropower is one of the leading Pelton Turbine manufacturers. Our Pelton Turbine Generator, Pelton Turbine Efficiency, Pelton Runner has high quality and competitive price, and you can see the Application Of Pelton Turbine.
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points.
Flow inside bucket
Shenyang Getai Hydropower Equipment Co.,Ltd main products: Pelton Turbine, Francis Turbine, Kaplan Turbine, Tubular Turbine, Pelton Turbine Generator, Francis Turbine Generator, Double Francis Turbine, Pelton Turbine Formula, welcome to our factory!
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter.
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
-1.0 |
≤ |
≤ |
|||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
Pelton Turbine Generator
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: |
50/60HZ |
Runner Diameter: |
~ 3m |
Lift Span |
30-50 years |
Getai Hydropower is one of the leading Pelton Turbine manufacturers. Our Pelton Turbine Generator, Pelton Turbine Efficiency, Pelton Runner has high quality and competitive price, and you can see the Application Of Pelton Turbine.
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter
Shenyang Getai Hydropower Equipment Co.,Ltd main products: Pelton Turbine, Francis Turbine, Kaplan Turbine, Tubular Turbine, Pelton Turbine Generator, Francis Turbine Generator, Double Francis Turbine, Pelton Turbine Formula, welcome to our factory!
Forged Entire CNC Machined Pelton Runner
Forging could considerably improve metal's organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear steel is generally stronger and more reliable than castings part.
Project Basic Information
Project Name: Minas-San Francisco HPP
Project Location: Ecuador
Pelton runner pitch diameter: 2460mm.
OD: 3179mm
Net Weight: 13300KG
Buckent No. 21
Output:
Product Introduction
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Getai Hydropower is Pelton Turbine Experiment, Francis Turbine Diagram, Francis Turbine Working, Pelton Turbine For Sale factoty.
Performance comparison table of forging parts and casting parts
Performance test of forging part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
|||||
Standard value |
≥795 |
≥620 |
≥15 |
≥45 |
≥50 |
230~295 |
|||||
Actual value |
Horizontal |
815 |
655 |
107 |
102 |
110 |
259 |
256 |
253 |
||
Vertical |
820 |
660 |
67 |
149 |
152 |
136 |
256 |
257 |
257 |
Performance test of casting part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
||||
Standard value |
≥750 |
≥550 |
≥15 |
≥35 |
≥50 |
221~286 |
||||
Actual value |
770 |
610 |
17 |
50 |
84 |
88 |
85 |
252 |
255 |
254 |
Forged Entire CNC Machined Francis Runner
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Getai Hydropower is a China supplier of Francis Turbine, Francis Turbine Generator, Francis Turbine Parts, Francis Runner, Construction And Working Of Francis Turbine. We have a complete quality management system. Choose us, you can be get most careful and thoughtful service!
Forged Integrally +100% CNC Machining Francis Turbine Runner
In the case the high head Francis runner with long and narrow passageway which is hard for entire CNC machining or the runner size exceeds the forging range which can not be forged integrally, GETAI applied a procedure by dividing the runner to two parts which consisted of crown with half vanes and band with rest half, both two parts can be forged integrally with entire CNC machining and welding assembled in final. The welding applied to the middle of vane, where is convenient for single pass welding without touch of potential crack area, the operation security and service life are improved largely.
Samples exhibited below is for forged integrally+100% CNC machined Francis turbine runner (half part) which finished by our five axis linkage CNC machine.
Getai Hydropower is Pelton Turbine Experiment, Francis Turbine Diagram, Francis Turbine Working, Pelton Turbine For Sale factoty.
Pelton Turbine
Pelton Runner, Pelton Turbine Generator, Pelton Turbine Forging China manufacturer Supplier
Pelton Turbine - Getai Turbine
Francis Turbine - Getai Turbine
Kaplan Turbine - Getai Turbine
Pelton Wheel Turbine
Water Turbine Generator
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Pelton Turbine Forging China manufacturer
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: Frecuencia: |
50/60HZ |
Runner Diameter: |
~ 3m |
Getai Hydropower is one of the leading Pelton Turbine manufacturers. Our Pelton Turbine Generator, Pelton Turbine Efficiency, Pelton Runner has high quality and competitive price, and you can see the Application Of Pelton Turbine.
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points.
Flow inside bucket
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter.
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
≤ |
≤ |
||||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
Pelton Turbine
Pelton Runner, Pelton Turbine Generator, Pelton Turbine Forging China manufacturer Supplier
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Pelton Turbine Forging China manufacturer
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: Frecuencia: |
50/60HZ |
Runner Diameter: |
~ 3m |
Getai Hydropower is one of the leading Pelton Turbine manufacturers. Our Pelton Turbine Generator, Pelton Turbine Efficiency, Pelton Runner has high quality and competitive price, and you can see the Application Of Pelton Turbine.
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points.
Flow inside bucket
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter.
Chemical Composition for ASTM A473 S41500 and ASTM A743 CA6NM(%)
Material No. |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
ASTM A473 S41500 |
≤ |
≤ |
-1.0 |
≤ |
≤ |
|||
ASTM A743 CA6NM |
≤ |
≤ |
≤ |
Mechanical Property for ASTM A473 S41500 and ASTM A743 CA6NM
Material No. |
σ(Mpa) |
σb(Mpa) |
δ5(%) |
ψ(%) |
Akv (J/cm2) |
HB |
ASTM A473 S41500 |
≥620 |
≥795 |
≥15 |
≥45 |
≥50 |
≤295 |
ASTM A743 CA6NM |
≥550 |
≥755 |
≥15 |
≥35 |
≥50 |
≤285 |
Pelton Turbine Generator
Pelton Turbine Generator, Hydraulic Turbine Generator, CFD Pelton Turbine wholesaler
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: |
50/60HZ |
Runner Diameter: |
~ 3m |
Lift Span |
30-50 years |
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter
Shenyang Getai Hydropower Equipment Co.,Ltd main products: Pelton Turbine, Francis Turbine, Kaplan Turbine, Tubular Turbine, Pelton Turbine Generator, Francis Turbine Generator, Double Francis Turbine, Pelton Turbine Formula, welcome to our factory!
Pelton Turbine Generator
Pelton Turbine Generator, Hydraulic Turbine Generator, CFD Pelton Turbine wholesaler
Pelton turbine is suitable for medium and high water head power plants. The key components are: Pelton runner, main shaft and Nozzle assembly.
Application Scope: Alcance de aplicación:
Water Head: |
100 ~ 1700m |
Output: |
300MW |
Frequency: |
50/60HZ |
Runner Diameter: |
~ 3m |
Lift Span |
30-50 years |
CFD analysis for Pelton turbine is performed in order to predict the turbine performance. The head loss in the collecting pipe and injector assembly is calculated based on CFD analysis results.
The relation of needle stroke and flow also can be calculated. CFD analysis can improve injector and nozzle design to reduce head los. The flow curve relative to needle stroke can be drawn based on analytical data.
CFD analysis can simulate the whole procedure which flow coming into and outgoing from bucket. The flow visualization can clearly show whether water flow outgoing from bucket pressure side hit the bucket back side. Such flow situation will cause more hydraulic loss and should be avoid during runner bucket optimum design process. The torque generated by runner and pressure distribution in the bucket can be calculated based on CFD analysis results. Turbine output and efficiency is finally predicted for various operating points
The possible location of cavitation can be predicted based on the pressure distribution in the bucket. The phenomena of cavitation should be avoided in the back tip of splitter by optimum design for back shape of splitter
Shenyang Getai Hydropower Equipment Co.,Ltd main products: Pelton Turbine, Francis Turbine, Kaplan Turbine, Tubular Turbine, Pelton Turbine Generator, Francis Turbine Generator, Double Francis Turbine, Pelton Turbine Formula, welcome to our factory!
Forged Entire CNC Machined Pelton Runner
CNC & Forged Pelton Runner, Pelton Turbine Forging, Pelton Turbine Generator China & Supplier
Forging could considerably improve metal's organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear steel is generally stronger and more reliable than castings part.
CNC & Forged Pelton Runner
Project Basic Information
Project Name: Minas-San Francisco HPP
Project Location: Ecuador
Pelton runner pitch diameter: 2460mm.
OD: 3179mm
Net Weight: 13300KG
Buckent No. 21
Output:
Pelton Turbine Forging Product Introduction
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Performance comparison table of forging parts and casting parts
Performance test of forging part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
|||||
Standard value |
≥795 |
≥620 |
≥15 |
≥45 |
≥50 |
230~295 |
|||||
Actual value |
Horizontal |
815 |
655 |
107 |
102 |
110 |
259 |
256 |
253 |
||
Vertical |
820 |
660 |
67 |
149 |
152 |
136 |
256 |
257 |
257 |
Performance test of casting part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
||||
Standard value |
≥750 |
≥550 |
≥15 |
≥35 |
≥50 |
221~286 |
||||
Actual value |
770 |
610 |
17 |
50 |
84 |
88 |
85 |
252 |
255 |
254 |
Forged Entire CNC Machined Pelton Runner
CNC & Forged Pelton Runner, Pelton Turbine Forging, Pelton Turbine Generator China & Supplier
Forging could considerably improve metal's organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear steel is generally stronger and more reliable than castings part.
CNC & Forged Pelton Runner
Project Basic Information
Project Name: Minas-San Francisco HPP
Project Location: Ecuador
Pelton runner pitch diameter: 2460mm.
OD: 3179mm
Net Weight: 13300KG
Buckent No. 21
Output:
Pelton Turbine Forging Product Introduction
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Performance comparison table of forging parts and casting parts
Performance test of forging part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
|||||
Standard value |
≥795 |
≥620 |
≥15 |
≥45 |
≥50 |
230~295 |
|||||
Actual value |
Horizontal |
815 |
655 |
107 |
102 |
110 |
259 |
256 |
253 |
||
Vertical |
820 |
660 |
67 |
149 |
152 |
136 |
256 |
257 |
257 |
Performance test of casting part
Mechanical Property |
σb(Mpa) |
σ(Mpa) |
δ5(%) |
ψ(%) |
AKV(J/cm²) |
HB |
||||
Standard value |
≥750 |
≥550 |
≥15 |
≥35 |
≥50 |
221~286 |
||||
Actual value |
770 |
610 |
17 |
50 |
84 |
88 |
85 |
252 |
255 |
254 |
Forged Entire CNC Machined Francis Runner
CNC Machined Francis Runner, Francis Runner Band Heat Treatment For Sale & Manufacturer
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Forged Integrally +100% CNC Machined Francis Runner
Francis Runner Band Heat Treatment For Sale
In the case the high head Francis runner with long and narrow passageway which is hard for entire CNC machining or the runner size exceeds the forging range which can not be forged integrally, GETAI applied a procedure by dividing the runner to two parts which consisted of crown with half vanes and band with rest half, both two parts can be forged integrally with entire CNC machining and welding assembled in final. The welding applied to the middle of vane, where is convenient for single pass welding without touch of potential crack area, the operation security and service life are improved largely.
Forged Entire CNC Machined Francis Runner
CNC Machined Francis Runner, Francis Runner Band Heat Treatment For Sale & Manufacturer
Forging could considerably improve metal’s organizational structure and mechanical property.
Forging offers uniformity of composition and structure. Forging results in metallurgical recrystalisation and grain refinement as a result of the thermal cycle and deformation process. This strengthens the resulting steel product particularly in terms of impact and shear strength.
Forged steel is generally stronger and more reliable than castings of same material due to the fact that the grain flows of the steel are altered, conforming to the shape of the part.
Forged Integrally +100% CNC Machined Francis Runner
Francis Runner Band Heat Treatment For Sale
In the case the high head Francis runner with long and narrow passageway which is hard for entire CNC machining or the runner size exceeds the forging range which can not be forged integrally, GETAI applied a procedure by dividing the runner to two parts which consisted of crown with half vanes and band with rest half, both two parts can be forged integrally with entire CNC machining and welding assembled in final. The welding applied to the middle of vane, where is convenient for single pass welding without touch of potential crack area, the operation security and service life are improved largely.