HFA Series Pleated High Flow Cartridges Replace to Pall Ultipleat High Flow Filters
Description
The large diameter geometrical design of polypropylene pleated high flow filter cartridges enlarge surface filtration area, high dirt holding capacity to save the quantities of filter cartridges, high flow rate when filtration efficiency exceed 99%. high flow filter cartridges are wide range of chemical compatibility and applications, the ideal option for industrial high flow water filtration system to protect RO membrane.
Feature
1. Gradient pore structure of high flow filter cartridges provide layered filter function
2. Outer hard cage can withstand higher pressure than Pall Ultipleat high flow filters made by soft netting
3. High flow filter cartridges are high filtration efficiency, lower waste disposal costs and more economical
4. Inside to outside filtration pattern of High flow filter cartridges ensure holding all impurities stay inside the pleated media
5. The highest flow rate of High flow filter cartridges could get 110 M3/H and Beta 5000 rated ( efficiency)
6. The reduction of filtration system space maximum 50% and lower maintenance costs when use High flow filter cartridges
7. Materials meet FDA requirements, wide chemical compatibility, no resins, binders, or adhesives and 100% integrity testing
Filter Media | Polypropylene(PP) Pleated |
Length | 20"(508mm), 40"(1016mm), 60"(1524mm) |
Outside Diameter | 6 inch (152mm) |
Inside Diameter | |
Filtration Rating | 1μm, 2μm, 3μm, 5μm, 10μm, 20μm, 40μm, 70μm, 100μm |
Support/Drainage | Polypropylene (PP) |
End Cap Material | Glass fiber reinforced Polypropylene (PP) |
Outside | Rigid Hard Cage, Stainless Steel(special) |
Seal Material | EPDM, Buna-N, Viton |
Operation Data for HFA Series Pall Ultipleat Replacement Pleated High Flow Filter Cartridges
Maximum Operating Temperature | 180°F @ 20 psid (82°C @ bar) |
160°F @ 30 psid (71°C @ bar) | |
77°F @ 50 psid (25°C @ bar) | |
Suggested Maximum Flow Of Water | 20inch length: 660 LPM |
40inch length: 1,300 LPM | |
60inch length: 1,900 LPM | |
Liquid Flow Direction | Inside to outside |
Typical Surface Area | ㎡ per 20" filter cartridge |
7㎡ per 40" filter cartridge | |
㎡ per 60" filter cartridge | |
Recommend Change out Differential Pressure | Bar at 20 ℃ |
Pressure-Drop Rate for 40" HFA Series Pall Ultipleat Replacement Pleated High Flow Filter Cartridges
Design for High Flow Filter Cartridges | ||
● The 3D high-end design show the advantages of structure HF Series pleated high flow filter cartridges ● The complete design is very important to research, development and manufacture of high flow pleated cartridges ● Powerful technical team can help to customize the special pleated high flow filters to replace Pall Ultipleat high flow filters ● Pay high attention to every detail, better design to create higher quality of high flow filter cartridges for water filtration system |
||
Installation for High Flow Filter Cartridges | ||
● Inside to outside flow pattern and no bypass ● Replace to Pall Ultipleat high flow filter directly ● Outside hard cage to make stable structure and reliably good sealing ● High flow rate & low delta pressure, absolute rated filters are designed ● Smaller and more economical filter systems, lower maintenance and waste disposal costs |
HFA | Material | Length | Filtration Rating |
O-ring Material |
Inside (selective) |
HFA Series Pall Ultipleat Replacement Pleated High Flow Filter Cartridges |
P = PP Pleated | 20 = 20"(508mm) | 1 = 1μm | E = EPDM | C = Central PP core |
2 = 2μm | |||||
3 = 3μm | |||||
40 = 40"(1016mm) | 5 = 5μm | B = Buna-N | |||
10 = 10μm | |||||
20 = 20μm | |||||
60 = 60"(1524mm) | 40 = 40μm | V = Viton | |||
50 = 50μm | |||||
70 = 70μm | |||||
100 = 100μm |
For Example:
HFA-P-40-5-E
HFA Series Pall Ultipleat Replacement Pleated High Flow Filter Cartridges - Material: Polypropylene - Length = 40" - Filtration Rating = 5μm - O-ring Material = EPDM
Special specifications high flow pleated cartridges can be customized, such as central PP core, special end caps or Stainless Steel outside cage etc.
PF series High Flow Cartridge Filters Parker Mega-flow high flow filter replacement
Description
Pleated High Flow Filters are made of advanced polypropylene microfiber, pleated filters are Parker high flow water filters replacement. Pleated high flow filters can directly replace Parker Megaflow and Fulflo series high flow pleated filters for high flow applications water filtration system. The water treatment volume for per pleated high flow filter cartridge equals to 10 pcs standard 40 inch length and " outer diameter water filter cartridges,inner single O-ring and double O-rings end caps insure no bypass and handle design makes more easier to install and change out.
Feature
Application
Filter Media | Polypropylene Pleated |
Length | 20"(508mm), 40"(1016 mm), 60"(1524mm) |
Outside Diameter | 6 inch(152mm) |
Filtration Rating | 1μm, 3μm, 5μm, 6μm,10μm, 20μm, 40μm, 70μm, 100μm |
Support/Drainage | Polypropylene (PP) |
End Cap Material | Glass fiber reinforced Polypropylene (PP) |
Seal Material | EPDM, Viton |
Outside | Netting |
Operation Data for PF Series Pleated High Flow Filters
Maximum Operating Temperature | 82℃ |
Maximum Differential Pressure | @ 82℃ |
Suggested Maximum Flow Rate | 20"(508mm) - 30m³/h |
40"(1016mm) - 50m³/h | |
60"(1524mm) - 70m³/h |
Flow Rate for Length: 40" PF Series Pleated High Flow Filters
Installation Example for PF Series Pleated High Flow Filters
● Pleated high flow filters have stable structure and reliably sealing ● High flow pleated filters are installed in standard high flow filter housings ● Long service life and easy to replace to Parker Megaflow and Fulflo series ● Geometry pleated structure, large filtration area and high dirt holding capacity ● High flow rate & low delta pressure, filters are designed for high filtration efficiency |
PF | Material | Length | Filtration Rating | Open End Type | O-ring Material |
PF Series Pleated High Flow Filters |
P = Polypropylene | 20 = 20"(508mm) | 1 = 1μm | S = Single O-ring | E = EPDM |
3 = 3μm | |||||
5 = 5μm | |||||
40 = 40"(1016mm) | 6 = 6μm | ||||
10 = 10μm | D = Double O-rings | V = Viton | |||
20 = 20μm | |||||
60 = 60"(1524mm) | 40 = 40μm | ||||
70 = 70μm | |||||
100 = 100μm |
For Example:
PF-P-40-5-D-E
PF Series Pleated High Flow Filters - Polypropylene - 40" (1016mm) - 5μm - Double O-rings - EPDM
MP Series Pleated High Flow Cartridges Replace to 3M Cuno High Flow Filters
Description
High Flow Pleated Cartridges have high particle removal efficiency and strong contaminant holding capability. PP pleated high flow cartridges utilize polypropylene end caps, outer netting and inner hard core help to protect the radial pleated structure integrity and provide consistent performance and good quality for effective particle retention. Pleated high flow cartridges can directly 100% replace to 3M Cuno 7000 and 740B high flow series filter element.
Feature
Application
Filter Media | Polypropylene |
Length | 20"(508mm), 40"(1016mm), 60"(1524mm) |
Outside Diameter | 6 inch () |
Inside Diameter | 3 inch () |
Filtration Rating | 1μm, 3μm, 5μm, 10μm, 20μm, 50μm, 70μm |
Support/Drainage | Polypropylene(PP) |
End Cap Material | Glass fiber reinforced Polypropylene(PP) |
Seal Material | EPDM, Buna-N, Silicon |
Operation Data for MP Series High Flow Pleated Cartridges
Suggested Maximum Flow Rate | 1560 LPM |
Maximum Operating Temperature | 80℃ |
Maximum Forward Differential Pressure | 50 psid @ 68°F ( bar @ 20°C) |
Recommended Change-out Differential Pressure | 35 psid @ 68° ( bar @ 20°C) |
Flow Rate for MP Series 5 micron High Flow Pleated Cartridges
Show Detail for High Flow Pleated Cartridges | ||
● Considerate designed handle easily for install and change out ● "Twist to lock" seating mechanism design to provide a positive seal ● 100% replace 3M Cuno 7000 and 740B high flow series filter element ● A large diameter core allows up to 500 gpm for per high flow pleated cartridges ● 2-3 times larger surface area than normal diameter 6" vertical pleated high flow cartridges |
||
High Flow Pleated Cartridges vs Depth & Pleated Cartridges | ||
● The High Flow System requires 90% fewer filter cartridges as competitive " cartridge systems for a requested flow rate. ● The High Flow Housings are 33% to 50% smaller than competitively sized housings for a requested flow rate, and save much space for when using pleated high flow cartridges. ● High efficiency filtration of high flow cartridge filters is a user-friendly high flow system, means fewer filters and faser change-outs than competitive cartridges. |
||
Installtion Example for MP Series High Flow Pleated Cartridges | ||
● Long service life and easy to replace, reduced cartridge handling ● High flow rate & low delta pressure, nominal rated filters are designed ● Cartridges are suitable to installed in standard high flow filter housings ● Radial pleated structure, large filtration area and high dirt holding capacity ● High flow pleated cartridges have rock-steady structure and reliably good sealing |
MP | Material | Length | Filtration Rating | End Caps | O-ring Material |
MP Series High Flow Pleated Cartridges |
P = Polypropylene | 20 = 20" | 1 = 1μm | A = Type A End Caps | E = EPDM |
3 = 3μm | |||||
40 = 40" | 5 = 5μm | N = Buna-N | |||
10 = 10μm | B = Type B End Caps | ||||
60 = 60" | 20 = 20μm | S = Silicon | |||
50 = 50μm | |||||
70 = 70μm |
For Example:
MP-P-40-5-A-E
MP Series High Flow Pleated Cartridges - Material = PP - Length = 40" - Filtration Rating = 5μm - Type A End Caps - O-ring Material = EPDM
MF series Pleated High Flow Filters 3M 740 series filter elements replacement
Description
Pleated High Flow Cartridges are designed to be used in different filter housings which install 1 to 37 pieces cartridge filters. Pleated high flow cartridges are made by polypropylene media, large filter area and high filtration efficiency exceed 99%. High flow cartridge filters can be used for a variety of important industrial applications for different high flow rate request. High flow pleated cartridges are used as a direct replacement to 3M 740 series elements, reduce the number of normal " OD filter cartridges save much cost and manpower, longer service life and high dirt holding capacity.
Feature
Application
Filter Media | Polypropylene Pleated |
Length | 20"(508mm), 40"(1016 mm), 60"(1524mm) |
Outside Diameter | 6 inch(152mm) |
Filtration Rating | 1μm, 3μm, 5μm, 10μm, 20μm, 40μm, 70μm, 100μm |
Support/Drainage | Polypropylene (PP) |
End Cap Material | Glass fiber reinforced Polypropylene (PP) |
Center Core | Polypropylene |
Outer Support Cage | Polypropylene |
Seal Material | EPDM, Viton |
Operation Date for MF Series Pleated High Flow Cartridges
Maximum Operating Temperature | 80℃ |
Maximum Differential Pressure | @ 82℃ |
Replacement recommend pressure drop | @ 20℃ |
Suggested Maximum Flow Rate | 40"(1016 mm) - 1300 LPM |
Flow Rate for 40" MF Series Pleated High Flow Cartridges
CAD Drawing for 40" MF Series Pleated High Flow Cartridges
● Inside core and outside cage ensure good performace under high pressure ● Long service life and easy to replace to3M 740 series high flow filter elements ● Pleated high flow cartridges are suitable to install for normal high flow filter housing ● Pleated cartridge save much cost and manpower, longer service life and high dirt holding capacity ● Good sealing O-ring design no bypass, high flow rate, low delta pressure & high filtration efficiency |
MF | Material | Length | Filtration Rating | End Caps | O-ring Material |
MF Series Pleated High Flow Cartridges |
P = PP Pleated | 20 = 20"(508mm) | 1 = 1μm | A = Type A End Caps | E = EPDM |
3 = 3μm | |||||
5 = 5μm | |||||
40 = 40"(1016mm) | 10 = 10μm | V = Viton | |||
20 = 20μm | B = Type B End Caps | ||||
40 = 40μm | |||||
60 = 60"(1524mm) | 70 = 70μm | ||||
100 = 100μm |
For Example:
MF-P-40-1-A-E
MF Series Pleated High Flow Cartridges - PP Pleated - 40" (1016mm) - 1μm - Type A End Caps - EPDM
BF Series High Flow Bag Filter Cartridges Pall Marksman Water Filters Replacement
Description
High Flow Pleated Bag Filters are made of high quality pleated depth polypropylene,replace to Pall Marksman Series filters and easily retrofit into existing Size 1 and Size 2 filter bag housings. One piece Size 2 high flow pleated bag filters replaces up to 16pcs standard 10"(254mm) depth filters, making change-outs quick and easy. High flow bag pleated filters are inside-to-outside fluid flow, combine the performance advantages of filter cartridges and filter bags which use in bag filter systems. High flow bag filters provide high quality benefits and economic value, the pleated design increase the effective filtration area with high flow rate, long service and lower operating costs.
Feature
Application
Filter Media | Polypropylene Pleated |
Nominal Length | 16"(405 mm) for size 1 bag, 31"(785 mm) for size 2 bag, 40" Length |
Outside Diameter | 6 inch(152mm) |
Filtration Rating | 1μm, 3μm, 5μm, 10μm, 20μm, 40μm, 70μm, 100μm |
Support/Drainage | Polypropylene (PP) |
End Cap Material | Polypropylene (PP) |
Outer Support Cage | Polypropylene (PP) |
Seal Material | EPDM, NBR |
Operation Date for BF Series High Flow Pleated Bag Filters
Maximum Operating Temperature | 70℃ |
Maximum Differential Pressure | bar @ 20℃ (75 psi @ 68°F) |
bar @ 54℃ (35 psi at 130°F) | |
Recommended Change out Differential Pressure | bar at 54℃ (35 psi at 130°F) |
Pressure-Drop for Size 1 High Flow Pleated Bag Filters
3D Drawing for BF Series High Flow Pleated Bag Filters
● Innovative push-in flanges enable quick and convenient change outs ● High surface area design provides high flow capacity and longer service life ● High flow bag filters are inside-out flow direction which is correspondent with bag filter ● No bypass, high flow capacity, all polypropylene construction and wide chemical compatibility ● Pleated bag filters manufactured by advanced thermal welding techniques, free of binders and additives |
|||||||||||
Installation Example for BF Series High Flow Pleated Bag Filters
● Inside-out flow effectively traps contaminants inside the filter elements ● Available to fit most Size 1 and Size 2 bag vessels with no hardware changes ● Replace to Pall Marksman Series filters and easily retrofit into existing Size 1 and Size 2 filter bag housings ● With advantages of big flow rate and high purity, fewer change outs and lower maintenance cost are required ● Innovative push-in flanges enable quick and convenient replacements into most commercial bag filter housings |
BF | Material | Nominal Length | Filtration Rating | O-ring Material |
BF Series High Flow Pleated Bag Filters |
P = Polypropylene | 1 = Size 1 Bag | 1 = 1μm | E = EPDM |
3 = 3μm | ||||
5 = 5μm | ||||
2 = Size 2 Bag | 10 = 10μm | |||
20 = 20μm | V = Viton | |||
40 = 40μm | ||||
40 = 40" Length | 70 = 70μm | |||
100 = 100μm |
For Example:
BF-P-2-5-E
BF Series High Flow Pleated Bag Filters - Polypropylene - Size 2 Bag - 5μm - EPDM
Description
PP Pleated Cartridge Filters are made of Polypropylene fiber media. PP pleated cartridge filters provide excellent filtration efficiency and chemical compatibility across a wide range of liquid filtration process constitution of nominal PP pleated filter cartridges adopt thermal welding techniques to seal all components, so no side leakage and optimizing PP pleated cartridge 100% integrity. PP pleated filter cartridges have large surface area that allow for greater system flow rate and higher dirt holding capacity than depth filters. PP pleated cartridges are widely used in prefiltration field requiring high purity.
Feature
components of PP pleated filters are assembled in fully sealed condition by thermal bond, free of binder
Applications
Filter Media | Polypropylene |
Length | 5", ", ", 10", 20", 30", 40" |
Outside Diameter | "(70mm) |
Filtration Rating |
, , , , , 1μm, 2μm, 3μm, 5μm, 10μm, 20μm, 30μm, 40μm, 50μm, 60μm |
Core | Polypropylene |
Support/Drainage | Polypropylene |
Gasket/O-ring | Silicone, EPDM, Viton, NBR, Teflon encapsulated Viton |
End Cap/Cage | Polypropylene |
End Cap Type | DOE, 222/Flat, 222/Fin, 226/Flat, 226/Fin, 215/Flat, 215/Fin |
Operation Data for PCF Series Nominal PP Pleated Cartridge Filters
Maximum Operating Temperature | 80℃(176℉) |
Max. Differential Pressure | bar at 20℃ (70 psi at 68℉) |
bar at 50℃ (50 psi at 122℉) | |
bar at 80℃ (20 psi at 176℉) | |
Maximum reverse pressure | 40 psid @ 70°F ( bar @ 21°C) |
Recommended Change Out Differential Pressure | bar (35 psid) |
Sterilization Temperature Time | 121˚C (250˚F) for 30 minutes at bar (14 psi) |
Pressure Drop Rate for 10" PP Pleated Cartridge Filters
Electron Microscopic Photo of PP Membrane
3D Drawing for PP Pleated Cartridge Filters | ||||||||||
● Thermal welding techniques ensure PP pleated filter cartridges no side leakage ● Ulti-layers pleated, low pressure drop, high capacity of impurities and long service life ● 100% integrity tested, ineer core and outside cage strengthen capacity of high flow pressure ● Large surface area that allow for high flow rate and higher dirt holding capacity than normal depth filters |
||||||||||
Installation Example for PP Pleated Cartridge Filters | ||||||||||
● Manufactured in continuous lengths up to 40 inches and vrious of filtration ratings ● Wide range of chemical compatibility used in prefiltration fields with high flow rate ● Special PP pleated cartridge filters can be made, such as special length and . inner core ● Various of end caps fit for standard filter housings, easy to install help to save some manpower and time |
||||||||||
End Caps of PP Pleated Cartridge Filters
PCF | Length | Micron Rating | End Cap | Gasket/O-ring | Adders |
PCF Series Nominal PP Pleated Cartridge Filters |
5 = 5" | = | A = Double Open End (DOE) | S = Silicone |
K = Thicker PP Cage |
= | |||||
= " | = | B = 222/Flat(SOE) | |||
= | E = EPDM | ||||
= " | = | C = 222/Fin(SOE) | |||
1 = 1μm | I = Stainless Steel Insert End Cap | ||||
10 = 10" | 2 = 2μm | D = 226//Flat(SOE) | N = NBR | ||
3 = 3μm | |||||
20 = 20" | 5 = 5μm | F = 226/Fin(SOE) | |||
10 = 10μm | V = Viton | ||||
30 = 30" | 20 = 20μm | G = 215/Flat(SOE) | S = Stainless Steel Core | ||
30 = 30μm | |||||
40 =40" | 40 = 40μm | H = 215/Fin(SOE) | T = Teflon Encapsulated Viton | ||
50 = 50μm | |||||
60 = 60μm |
For Example:
PCF-10-1-B-S
PCF Series Nominal PP Pleated Cartridge Filters - 10" - 1μm - 222/Flat(SOE) - Silicone O-ring
Description
Absolute PP pleated filters are constructed with 100% advanced polypropylene materials and assembled by high technology thermal bonding equipment. Absolute PP pleated cartridges are offered in absolute rate Beta 5000(to ) retention efficiencies. Absolute pleated filter cartridges are wide chemical compatibility using 100% polypropylene materials comply with FDA, an ideal choice for efficient filtration of critical industries.
Feature
Applications
Filter Media | Polypropylene |
Length | 5", ", ", 10", 20", 30", 40" |
Outside Diameter | "(70mm) |
Filtration Rating | , , , , , 1μm, 2μm, 3μm, 5μm, 10μm, 20μm, 30μm, 40μm, 50μm, 60μm |
Core | Polypropylene, Stainless Steel |
Support/Drainage | Polypropylene |
Gasket/O-ring | Silicone, EPDM, Viton, NBR, Teflon encapsulated Viton |
End Cap/Cage | Polypropylene |
End Cap Type | DOE, 222/Flat, 222/Fin, 226/Flat, 226/Fin, 215/Flat, 215/Fin |
Operation Data for Absolute PP Pleated Filter Cartridges
Maximum Operating Temperature | 80℃(176℉) |
Max. Differential Pressure | bar at 20℃ (70 psi at 68℉) |
bar at 50℃ (50 psi at 122℉) | |
bar at 80℃ (20 psi at 176℉) | |
Maximum reverse pressure | 40 psid @ 70°F ( bar @ 21°C) |
Recommended Change Out Differential Pressure | ΔP 35 psi |
Filtered Hot Water | 80˚C for 30 min |
Sterilization Temperature Time | 121˚C (250˚F) for 30 minutes, multiple cycles |
Electron Microscopic Photo of Absolute PP Membrane
3D Drawing for Absolute PP Pleated Filter Cartridges | ||||
● Ulti-layers pleated, low pressure drop, high capacity of impurities and long service life ● 100% integrity tested, ineer core and outside cage strengthen capacity of high flow pressure ● Thermal welding techniques ensure Absolute PP Pleated Filter Cartridges no side leakage ● Large surface area allow for high flow rate and higher dirt holding capacity than normal depth filters |
||||
Installation Example for Absolute PP Pleated Filter Cartridges |
||||
● Manufactured in continuous lengths up to 40 inches ● Easy to install help to save some manpower and time ● Many kinds of end caps fit for standard filter housings ● Wide range of chemical compatibility used in prefiltration fields ● Various gaskets/O-ring material compatible with a variety of fluids ● Special Absolute PP Pleated Filters can be made, such us . inner core |
End Caps of Absolute PP Pleated Filter Cartridges
APC | Length | Micron Rating | End Cap | Gasket/O-ring | Adders |
APC Series Absolute PP Pleated Filter Cartridges |
5 = 5" | = | A = Double Open End (DOE) | S = Silicone | T = Thicker PP Cage |
= | |||||
= " | = | B = 222/Flat(SOE) | |||
= | E = EPDM | ||||
= " | = | C = 222/Fin(SOE) | |||
1 = 1μm | I = Stainless Steel Insert End Cap | ||||
10 = 10" | 2 = 2μm | D = 226//Flat(SOE) | N = NBR | ||
3 = 3μm | |||||
20 = 20" | 5 = 5μm | F = 226/Fin(SOE) | |||
10 = 10μm | V = Viton | ||||
30 = 30" | 20 = 20μm | G = 215/Flat(SOE) | S = Stainless Steel Core | ||
30 = 30μm | |||||
40 =40" | 40 = 40μm | H = 215/Fin(SOE) | T = Teflon Encapsulated Viton | ||
50 = 50μm | |||||
60 = 60μm |
For Example:
APC-20-5-A-S
APC Series Absolute PP Pleated Filter Cartridges - 20" - 5μm - Double Open End (DOE) - Silicone Gasket
Description
PET pleated cartridges are produced using 100% synthetic fibers, which are free of binders or adhesives, exhibit highly effective retention efficiency, also are washable and reusable commodiously. Polyester pleated filter cartridges also called water replacement filters, the pleated design increased surface area and extends service life, makes PET pleated cartridges to be one of the most economic options in water treatment.
Feature
Applications
Filter Media | Polyester (PET) |
Length | 5", ", ", 10", 20", 30", 40" |
Outside Diameter | "(68mm) |
Inside Diameter | " (28mm) |
Filtration Rating | 1μm, 5μm, 10μm, 20μm, 30μm, 50μm, 100μm |
Core | Polypropylene |
Outer Netting | Polypropylene |
End Caps/Gaskets | Plastisol/Polyurethane |
End Cap Type | Double Open End (DOE) |
Operation Data for Polyester Pleated Filter Cartridges
Maximum Operating Temperature | 75℃(167℉) |
Max. Differential Pressure | bar at 20℃ (70 psi at 68℉) |
bar at 50℃ (50 psi at 122℉) | |
Maximum reverse pressure | 40 psid @ 70°F ( bar @ 21°C) |
Recommended Change Out Differential Pressure | bar (35 psid) |
Pressure Drop Rate for 10" Polyester Pleated Filter Cartridges
● Hongtek end cap is made of high quality Polyurethane, smooth surface is good for sealing, when others made of inferior glue and rough
● Hongtek PET pleated filters are tightening pleated with larger filtration area, when others are sparse pleated counts with less surface area
● The Pleated counts of Hongtek polyester pleated cartridges is equal or greater than 60, when low quality made less than 60 pleated counts
● Hongtek PET pleated cartridges have advanced outer netting to strengthen the whole construction, others don't make good neat outer netting
PET | Length | Micron Rating | Outside |
PET Series Polyester Pleated Filter Cartridges |
5 = 5" | 1 = 1μm | W = With PP Netting |
= " | 5 = 5μm | ||
= " | 10 = 10μm | ||
10 = 10" | 20 = 20μm | ||
20 = 20" | 30 = 30μm | O = Without Netting | |
30 = 30" | 40 = 40μm | ||
40 =40" | 50 = 50μm | ||
100 = 100μm |
For Example:
PET-10-5-W
PET Series Polyester Pleated Filter Cartridges - 10" - 5μm - With PP Netting
Description
Backwashable PP Pleated Cartridges are mainly designed for power plant condensed water filtration. PP Filter media of backwashable pleated cartridges are available in absolute ratings ranging from 1 to over 100 microns to meet the removal requirements of each individual condensate system. Like all the condensate filter cartridges from Hongtek, a variety of end fittings can be selected to retrofit the elements in existing power plant condensate filter systems.
Feature
Applications
Filter Media | Polypropylene |
Length | 60"(1524mm), 70"(1778mm) |
Outside Diameter | "(70mm) |
Filtration Rating | 1μm, 3μm, 5μm, 10μm, 20μm, 50μm, 100μm |
Core | Polypropylene |
Support/Drainage | Polypropylene |
Gasket/O-ring | Silicone, EPDM, Viton, NBR |
End Cap/Cage | Polypropylene |
End Cap Type | DOE, 222/Flat, 222/Fin, 226/Flat, 226/Fin, 215/Flat, 215/Fin |
Maximum Operating Temperature | 80℃(176℉) |
Max. Differential Pressure | bar at 20℃ (58 psi at 68℉) |
bar at 60℃ (29 psi at 140℉) | |
bar at 80℃ (20 psi at 176℉) | |
Maximum reverse pressure | bar at 80℃ (14 psi at 176℉) |
Recommended Change Out Differential Pressure | bar (29 psi) |
Display of Backwashable PP Pleated Cartridges
● Backwashable PP pleated cartridges are easy to maintenance and lower change out costs
● High surface area of superior pleated media, high dirt holding capacity, removal efficiency rated at
● A variety of end fittings can be selected to retrofit the elements in existing power plant condensate filter systems
● 60 inchs & 70 inchs backwashable PP Pleated Cartridges are mainly designed for power plant condensed water filtration
BCF | Length | Micron Rating | Gasket/O-ring | End Cap |
BCF Series Backwashable PP Pleated Cartridges |
60 = 60" | 1 = 1μm | S = Silicone | DOE = Flat Gaskets Double Open End |
3 = 3μm | 2E = 2-222 O-ring with Flat End |
|||
5 = 5μm | E = EPDM | 6E = 2-226 O-ring with Flat End |
||
10 = 10μm | 2F = 2-222 O-ring with Fin |
|||
70 = 70" | 20 = 20μm | N = NBR | 6F = 2-226 O-ring with Fin |
|
50 = 50μm |
ES = Extended PP & . Thread Adapter |
|||
100 = 100μm |
V = Viton |
For Example:
BCF-60-5-S-ES
BCF Series Backwashable PP Pleated Cartridges - 60" - 5μm - Silicone - Extended PP & . Thread Adapter
Description
PP melt blown filter cartridges are high dirt holding capacity, low pressure drop, high flow rate, good chemical resistance, no fibre release, longer service life and effectively filtration for suspended particle, sediment and other kinds of impurities. PP melt blown cartridges are economical and classical filter media, widely used in liquid prefiltration industries.
Feature
Applications
Filter Media | Polypropylene |
Length | 5", ", ", 10", 20", 30", 40", 50", 60", 70" (According to customers requirements) |
Inside Diameter | 28mm, 30mm (Special ID is accepted) |
Outside Diameter | "(60mm), "(61mm), "(63mm), 5"(65mm) (Special OD is accepted) |
Filtration Rating | 1μm, 5μm, 10μm, 20μm, 30μm, 50μm, 75μm, 100μm |
Gasket/O-ring | Silicone, EPDM, Viton, Buna |
End Cap | DOE, 222/Flat(SOE), 222/Fin(SOE), 226/Flat(SOE), 226/Fin(SOE) |
Operation Data for PP Melt Blown Filter Cartridges
Maximum Operating Temperature | 60 ℃(140℉) |
Max. Differential Pressure | bar at 27℃ (43 psi at 80℉) |
bar at 60℃(29 psi at 140℉) | |
bar at 60℃(14 psi at 140℉) | |
Liquid Flow Direction | Outside to inside |
Recommend Change out Differential Pressure | Bar |
Pressure Drop Rate of 10" PP Melt Blown Filters
Construction of PP Melt Blown Filter Cartridges | ||
● The cross-section drawn of PP melt blown filter cartridges ● From inner layers to outer layers of PP filters the fiber is fine to coarse ● Multilayered structure and depth filtration pattern ensure good filtration efficiency ● Formed by thermal bond without using of any binders, adhesives and and lubricants ● 100% FDA approved polypropylene for compatibility with wide range of process fluids |
||
Working Principle of PP Melt Blown Cartridges |
||
● The drawing is the working principle of layers structure depth pp melt blown filter cartridge ● Layers filtration keep pp melt blown filter high flow rate, good filtration efficiency and long service life ● Large particles are filtered in outer layers of melt blown cartridges which are constructed by coarse fiber ● Small particles pass the outer layers, then filtered by inner layers wich made of fine fiber and high precision |
Installation of 40" 5 Micron PP Melt Blown Filter Cartridges
● Hongtek brand depth PP melt blown filters used for pre RO water filtration
● The central of PP filter elements are still no polluted, so that keep liquid clear after filtration
● After used PP filters compare with before used can apparent know the good efficiency filtration
● High quality and reasonable price melt blown cartridges increase of longer service life and save much cost
● No fiber drop out, high dirt holding, low pressure drop, high flow rate and high pressure resisting capability
NPP | ID | OD | Micron Rating | Length | End Cap | Gasket/O-ring |
NPP Series Nominal PP Melt Blown Filter Cartridges |
A = 28mm | C = 60mm | 1 = 1μm | 5 = 5" | D = DOE | S = Silicone |
5 = 5μm | = " | |||||
Q = 61mm | 10 = 10μm | = " | T = 222/Flat(SOE) | E = EPDM | ||
20 = 20μm | 10 = 10" | |||||
M = 63mm | 30 = 30μm | 20 = 20" | O = 222/Fin(SOE) | V = Viton | ||
B = 30mm | 50 = 50μm | 30 = 30" | ||||
75 = 75μm | 40 = 40" | P = 226/Flat(SOE) | ||||
F = 65mm | 50 = 50" | U = Buna | ||||
100 = 100μm | 60 = 60" | L = 226/Fin(SOE) | ||||
70 = 70" |
For Example:
NPP-A-M-5-40-D
NPP Series Nominal PP Melt Blown Filter Cartridges - 28mm - 63mm - 5μm - 40" - Double Open End (DOE)
Special specifications PP Melt Blown Filter Cartridges can be customized, such as special ID, OD, length and end caps etc.
Description
PP String Wound Cartridge Filters are manufactured by honeycomb construction with FDA approved polypropylene wound yarn material, outer layers are loose while inner layers are tight. Hongtek use computer modeling process which optimizes pp string wound cartridges geometrically and maximizes the use of cartridge surface area by the diamond-shaped depth filtration cones.
Feature
Application
Filter Media | Polypropylene |
Length | 5", ", ", 10", 20", 30", 40", 50" (According to customers requirements) |
Inside Diameter | 28mm, 30mm (Special ID can be customized) |
Outside Diameter | "(61mm), "(63mm), 5"(65mm) Special OD is accepted |
Filtration Rating | 1μm, 5μm, 10μm, 20μm, 30μm, 50μm, 75μm, 100μm |
Core | PP, SUS304, SUS316 |
Gasket/O-ring | Silicone, EPDM, Viton, Buna |
End Cap | DOE, 222/Flat(SOE), 222/Fin(SOE), 226/Flat(SOE), 226/Fin(SOE) |
Operation Data for PP String Wound Cartridge Filters
Maximum Operating Temperature | 60 ℃(140℉) |
Max. Differential Pressure | bar at 27 ℃(50 psi at 80℉) |
bar at 60 ℃(20 psi at 140℉) | |
bar at 82 ℃(10 psi at 180℉) | |
Liquid Flow Direction | Outside to inside |
Recommend Change out Differential Pressure | 1 bar (14 psi) |
Pressure Drop vs Flow Rate of 10" PP String Wound Cartridge Filters
Construction of PP String Wound Cartridge Filters | ||
● The picture is the cross-section of pp wound cartridges ● High dirt holding capacity,high flow rate and long service time ● From outer layers to inner layers the wound yarn are loose to tight ● Honeycomb construction without using adhesives and no fine fibre drop out ● Multilayered structure and depth filtration pattern ensure good filtration efficiency ● High quality pp string wound filters for compatibility with wide range of process fluids |
Production of PP String Wound Cartridge Filters
● Wound Yarn Materials: All pp wound yarns are made of high quality FDA approved nonpollution pp materials, so keep the advantage of filter material industry
● Filters Workshop: One of largest workshop of pp string wound filters China, high out put & fast delviery time, superior quality, excellent management system
● Wound Cartridges Warehouse: Scientific storage and warehouse of pp wound cartridges are also important, clean and moisture-resistant warehouse to the benefit of good delivery efficiency
● Container Shipment: PP string wound cartridges are convenient to be loaded into containers, forklift is quick action for cartons or pallets, save some spaces and times, safety transport for the shipment
PSW | ID | OD | Micron Rating | Length | Core Material | End Cap | Gasket/O-ring |
PSW Series PP String Wound Cartridge Filters |
A = 28mm | C = 61mm | 1 = 1μm | 5 = 5" | P = PP | D = DOE | S = Silicone |
5 = 5μm | = " | ||||||
M = 63mm | 10 = 10μm | = " | T = 222/Flat(SOE) | E = EPDM | |||
20 = 20μm | 10 = 10" | S4 = SUS 304 | |||||
B = 30mm | 30 = 30μm | 20 = 20" | O = 222/Fin(SOE) | V = Viton | |||
F = 65mm | 50 = 50μm | 30 = 30" | |||||
75 = 75μm | 40 = 40" | S6 = SUS 316 | P = 226/Flat(SOE) | U = Buna | |||
100 = 100μm | 50 = 50" | L = 226/Fin(SOE) |
For Example:
PSW-A-M-5-40-P-D
PSW Series PP String Wound Cartridge Filters - 28mm - 63mm - 5μm - 40" - PP Core - Double Open End (DOE)
Special specifications PP String Wound Cartridge Filters can be customized, such as special ID, OD, length and end caps etc.
Description
Carbon Block Cartridge Filters are made of activated carbon block which is manufactured by strictly extruded controlled engineering processes,advanced techniques and FDA approved material of the high quality activated carbon guarantee excellent durability, minimal pressure loss and high flow rate. Carbon block cartridges are highly effective in removing odour, bad taste, chlorine spores and microorganisms in water. Carbon block cartridge filters provide economic solution for a wide range of residential, commercial and industrial water filtration processing.
Feature
Application
Filter Media | Coal, Coconut Shell Activated Carbon |
Length | 5", ", ", 10", 20", 30", 40" (According to customers requirements) |
Inside Diameter | 28mm, 30mm (Special ID can be customized) |
Outside Diameter | "(63mm), 5"(65mm) Special OD is accepted |
Filtration Rating | 5μm, 10μm |
End Cap | Polypropylene |
Inner/Outer Wrap | Polypropylene Non-woven fabric |
Gasket/O-ring | Silicone, Buna-N, EPDM |
Netting | Polyethylene |
Operation Data for Carbon Block Cartridge Filters
Maximum Operating Temperature | 80℃(176℉) |
Max. Differential Pressure | bar at 25℃ (100 psi at 77℉) |
Pressure | 17 bar |
Recommended Change Out Differential Pressure | bar (31 psi) |
Max. Flow Rate | 5 L/min ( water, △P=㎡, 10" Carbon Block Cartridge) |
Efficiency & Flow Rate 10" CTO Carbon Block Cartridge Filters
Removability to Multifarious Impurities
Remaining chloride | Chemical oxygen demand | Total iron | Oxide | Mercury | As | Cyanide | Phenol | Sixivalency |
Average Adsorption to Poison Substance for 10" Carbon Block Cartridge Filters
Benzne | Toluene | Methanol | Ethoxy | Chloroform | Acetone | Styrene | Hyaarogen sulphide |
N-butyl sulfhydrate |
68g | 81g | 69g | 91g | 120g | 72g | 60g | 125g | 171g |
Technical Index of Activated Carbon
Ratio for surface area | 800 - 1000 m²/g |
Adsorption for iodine | 900-1000 mg/g |
Adsorption for Benzene | 20-25% |
Adsorption for carbon tetrachloride | 50-60% |
Adsorption for Methylene Bule | 13-16ml/g |
Ash content | ≤ |
Construction of Carbon Block Cartridge Filters | ||
● Outer layer is polypropylene non-woven fabric to filter the impurities & sludge ● Inner layer has high quality PP non-woven fabric to block carbon powder drop of ● Carbon block cartridges can be made of coal & coconut shell accodring to requirement ● The length size of OD and ID can be manufactured according to customer's requirement ● End cap is made of FDA approved polypropylene material, it is reliably sealing & durable ● A variety of filtration rating to ensure high filtration efficiency of remove residual chlorine ● O-ring can be made of Silicone, Buna-N, EPDM, high temperature resistant & good sealing |
CTO | Filter Material | Length | ID | OD | Micron Rating | Gasket/O-ring |
CTO Series Extruded Carbon Block Cartridge Filters |
A = Coal | 5 = 5" | C = 28mm | M = "(63mm) | 5 = 5μm | S = Silicone |
= " | ||||||
= " | ||||||
10 = 10" | E = EPDM | |||||
B = Coconut Shell | 20 = 20" | D = 30mm | F = 5"(65mm) | 10 = 10μm | ||
30 = 30" | U = Buna | |||||
40 = 40" |
For Example:
CTO-B-10-C-M-5-S
CTO Series Extruded Carbon Block Cartridge Filters - Coconut Shell - 10" - 28mm - 63mm - 5μm - Silicone
Special CTO Series Extruded Carbon Block Cartridge Filters can be customized, such as special ID, OD, length and end caps etc.
Description
Standard Felt Liquid Filter Bags are made of high quality polypropylene, polyester & Nomexfelt materials which provide consistent of performance of liquid filtration in various of critical industries. Standard felt liquid filter bags offer efficient depth filtering at increased flow rates, glazed outer and plain inner finish to reduce fiber migration and enhance filtration performance.
Feature
Application
Filter Media | Polypropylene Felt, Polyester Felt, Nomex Felt |
Bag Dimensions | Size 1: Ø7"×" |
Size 2: Ø7"× 32" | |
Size 3: Ø4"× 8" | |
Size 4: Ø4"× 14" | |
Filtration Rating | 1, 5, 10, 25, 50, 75, 100, 150, 200, 300μm |
Ring Style | Galvanized Steel O-Ring, Plastic Ring, . O-Ring |
Seam | Welded, Sewing, Welded top & Sewing Bottom, Sewing top & Welded Bottom |
Operation Data for Standard Felt Liquid Filter Bags
Filter Media | Polypropylene Felt | Polyester Felt | Nomex Felt |
Abrasion & Flex | Good | Good | Excellent |
Weak Acid | Excellent | Good | Excellent |
Strong Acid | Excellent | Good | Excellent |
Weak Alkali | Excellent | Good | Excellent |
Strong Alkali | Excellent | Poor | Excellent |
Solvents | Fair | Good | Good |
Maximum Operating Temperature | 70℃(160℉) | 160℃(320℉) | 250℃(500℉) |
Maximum Differential Pressure | bar ( psi) | ||
Recommended Change Out Differential Pressure | bar (15 psi) |
Pressure Drop vs Flow Rate of Standard Felt Liquid Filter Bags
Working Principle of Standard Felt Liquid Filter Bags | ||
● The drawing is the working principle of standard felt liquid filter bags ● Dirty fluid flow through the plain inner finish layer and large particle block in surface ● Felt filter media traps contaminants within its depth, no sliding sideways during processing ● Clean fluid come out from glazed layer, high filtration efficiency and long service life with low cost |
SFB | Filter Media | Bag Dimensions | Filtration Rating | Ring Style | Seam |
SFB Series Standard Felt Liquid Filter Bags |
P = Polypropylene Felt | 1 = Size 1: Ø7"×" | 1 = 1 μm | G = Galvanized Steel O-Ring | W = Fully Welded |
5 = 5 μm | |||||
10 = 10 μm | |||||
E = Polyester Felt | 2 = Size 2: Ø7"× 32" | 25 = 25 μm | S = Plastic Ring | F = Fully Sewing | |
50 = 50 μm | |||||
75 = 75 μm | |||||
N = Nomex Felt | 3 = Size 3: Ø4"× 8" | 100 = 100 μm | Q = Welded Top & Sewing Bottom | ||
150 = 150 μm | U = . O-Ring | ||||
4 = Size 4: Ø4"× 14" | 200 = 200 μm | T = Sewing Top & Welded Bottom | |||
300 = 300 μm |
For Example:
SFB-P-1-5-S-W
SFB Series Standard Felt Liquid Filter Bags - Polypropylene Felt - Size 1: Ø7"×" - 5 μm - Plastic Ring - Fully Welded
Special specifications Standard Felt Liquid Filter Bags can be customized, such as special bag dimensions, ring style and seam etc.
Description
Big Blue Polyester Pleated Cartridges are made of high quality polyester filter media and designed for general water filtration purposes, have low pressure drop and high flow capacity. Big Blue polyester pleated cartridges offer high retention efficiency. Polyester filter media of big blue polyester cartridges, central PP corn and plastisol end caps as a whole bonding together, welded to ensure no bypass. Big Blue polyester filters are washable and reusable commodiously. Numerous pleated counts enlarge surface area, durable and improving filtration efficiency.
Feature
Applications
Filter Media | Polyester (PET) |
Length | ", 10", 20", 30", 40" |
Outside Diameter | " |
Inside Diameter | " (28mm) |
Filtration Rating | 1μm, 5μm, 10μm, 20μm, 30μm, 50μm, 100μm |
Core | Polypropylene |
Outer Netting | Polypropylene |
End Caps/Gaskets | Plastisol/Polyurethane |
End Cap Type | Double Open End (DOE) |
Operation Data for Big Blue Polyester Pleated Cartridges
Maximum Operating Temperature | 75℃(167℉) |
Max. Differential Pressure | bar at 20℃ (70 psi at 68℉) |
bar at 50℃ (50 psi at 122℉) | |
Maximum reverse pressure | 40 psid @ 70°F ( bar @ 21°C) |
Recommended Change Out Differential Pressure | bar (35 psid) |
Pressure Drop vs Flow Rate for 10" Big Blue Pleated Cartridge
● Big Blue polyester pleated filters are tightening pleated with larger filtration area, others are sparse pleated counts with less surface area
● Hongtek end cap is made of high quality Polyurethane, smooth surface is good for sealing, low quality end caps are made of inferior glue
● Big Blue polyester pleated cartridges have advanced outer netting to strengthen the whole construction, others don't make good outer netting
● The Pleated counts of Hongtek big blue polyester pleated cartridges is equal or greater than 70, low quality made less than 70 pleated counts
BPC | Length | Micron Rating | Outside |
BPC Series Big Blue Polyester Pleated Cartridges |
= " | 1 = 1μm | W = With PP Netting |
10 = 10" | 5 = 5μm | ||
20 = 20" | 10 = 10μm | ||
30 = 30" | 20 = 20μm | ||
30 = 30μm | O = Without Netting | ||
40 =40" | 50 = 50μm | ||
100 = 100μm |
For Example:
BPC-10-1-W
BPC Series Big Blue Polyester Pleated Cartridges - 10" - 1μm - With PP Netting